Pinout
What each pin of the AC791N does on the FM-1, from working drivers. “Port” registers are at 0x50000 + 0x40 × port (A=0, B=1, C=2, H=7) with OUT +0, IN +4, DIR +8 (1 = input), DIE +0xC (digital input enable), PU +0x10, PD +0x14, HD0 +0x18, HD +0x1C. [SDK] [CODE]
SMK-37 wiring differs: see SMK-37.
| Pin | Function | Notes | Tag |
|---|---|---|---|
| PA0 | Matrix row (encoders) | pull-up, low = closed | [CODE] |
| PA1 | 74HC595 latch (RCLK) | [CODE] [HW] | |
| PA2 | LCD backlight, active low | also enables the key matrix (below) | [HW] |
| PA3 | 74HC595 clock (SRCLK) | [CODE] [HW] | |
| PA4 | 74HC595 data (SER) | [CODE] [HW] | |
| PA5–PA8 | Matrix rows | pull-ups; low = closed | [CODE] [HW] |
| PA9, PA10 | LED lines | light the LED in the selected column | [CODE] [HW] |
| PB1 | ADC ch 3: battery divider | never drive low (resets the chip after 8 s) | [CODE] |
| PB6 | ADC ch 4: MASTER pot | [CODE] | |
| PB7 | Matrix row (encoder 6) | [CODE] | |
| PC0, PC1, PC2, PC6 | Audio output-stage control lines | driven during audio bring-up; meaning of each not documented | [CODE] [?] |
| PC7 | LCD CS, active low | SPI1 | [CODE] [HW] |
| PC8 | LCD D/C (0 command, 1 data) | [CODE] [HW] | |
| PC9 | LCD SPI clock | [CODE] [HW] | |
| PC10 | LCD SPI data out | [CODE] [HW] | |
| PH6, PH9 | LED lines | [CODE] [HW] | |
| PH8 | TRS MIDI in → UART1 RX | 31250 baud, through input channel 1 | [CODE] |
| USB D+/D− | USB0 full-speed device | also the USB_KEY recovery signal (Recovery) | [HW] |
The package pins, from the resource hub
The FM-1 resource hub (§1.2) maps every pin of the 48-pin package, from Felucca-family drivers, board photos, JieLi’s AC7911B datasheet and reference schematics. Where it goes beyond the drivers, it is [?] here until someone checks it on a board:
| Pin(s) | The hub says | Tag |
|---|---|---|
| PC0, PC1, PC2, PC6 | I2S MCLK, BCLK, LRCK, and the codec’s power/reset line (active high), to an external codec | [?] |
| DACL (pin 13) | the chip’s own DAC, left channel, as an auxiliary line next to the codec | [?] |
| PD0, PD1, PD4, PD5, PD6 | the internal flash: CS, DI, CLK, DO, and a flash power gate | [?] |
| PH8 / PH7 | share one package pin; PH7 is UART1 TX on the die, but the TRS jack’s input circuit only passes MIDI in | [?] |
| 74HC595 outputs | 16 outputs, 11 used as columns: 5 spare outputs on the second register | [CODE] [?] |
| All 48 pins | in use: no free GPIO pad to solder to | [?] |
The hub also suggests ways to get a MIDI out (routing UART1 TX to the USB D+ pin when no computer is attached, or to a freed pin through the output crossbar). Nobody has published one working. [?]
The key matrix and PA2
[HW] “PA2 MUST be driven low while the FM-1 matrix is scanned.” On the FM-1, PA2 (the backlight enable) also enables the key matrix: with PA2 high or left as an input, no key reads closed. The ROM leaves PA2 undriven, so a key check at start-up sees nothing until PA2 is driven low (m-bootloader SPEC §8.2). A bootloader menu or a “hold a key at power-on” feature must drive PA2 low first; this also turns the backlight on.
Matrix layout
[CODE] 11 columns selected through the shift registers (a column’s bit low = selected; idle word FFFF), 6 rows read on PA0, PA5, PA6, PA7, PA8 and PB7. Felucca’s key map (hal/fm1_input.h, GPL-3.0-only):
/* key id at (physical column, packed row bit), -1 = none;
* ids 0..13 buttons, 14..40 note keys (note 0 = F3 .. 26 = G5) */
static const int8_t FM1_KEYMAP[6][11] = {
{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* PA0: encoders */
{ 5, 11, 4, 10, 3, 9, 2, 8, -1, -1, -1}, /* PA5 */
{34, 35, 36, 37, 38, 40, 39, 13, 7, 6, 12}, /* PA6 */
{23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33}, /* PA7 */
{ 0, 1, 15, 14, 17, 16, 19, 18, 20, 21, 22}, /* PA8 */
{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* PB7: encoder 6 */
};
Button 0 is OCT−, button 1 is OCT+. The other button ids map to the panel’s labelled buttons in each firmware’s own table. For the bootloader keys, m-bootloader reads OCT− on PA8 with column word F7FE, OCT+ on PA8 with EFFD, PLAY on PA6 with FBFF, REC on PA6 with FF7F [HW].
Allow ~10 µs after selecting a column before reading the rows. [CODE] [HW]
Sources
- Felucca’s HAL (
hal/fm1_gpio.h,fm1_input.h,fm1_lcd_hw.h,fm1_adc.h,fm1_audio.h,fm1_uart.h; GPL-3.0-only, © Leo Kuroshita), as in DUB-1. - m-bootloader SPEC.md §2.2, §8.2, §8.4.
- felucca-bsp
boards/fm1/. - FM-1 resource hub REVERSE_ENGINEERING.md §1.2 (commit
d269391, 2026-10-28; no licence declared, summarised only).
Unofficial community wiki. Not affiliated with M-VAVE or JieLi. Text under CC BY-SA 4.0; code excerpts keep their own licences (License). Facts are tagged [HW] [SDK] [RE] [CODE] [?]: see Home. Found an error? See Contributing. Home